How to Install a DIY Board and Batten Wall (2024)

A DIY board and batten wall can add depth and visual interest to your interior that's unachievable with ordinary painted drywall. While there are many DIY accent walls across the internet labeled "board and batten," a true board and batten wall feature narrow vertical battens covering the seams between wider vertical boards.

Often associated with farmhouse style, board and batten walls look great in several home styles, like modern, minimalistic, and coastal. While this exterior siding style started as an effective rain-shedding solution for exterior walls, it has made its way into interiors as a purely decorative element.

Before You Begin

To better understand the difference between traditional board and batten and the interior iteration we've outlined in this tutorial, we've broken them down below:

  • Traditional Method: Traditional board and batten consist of installing vertical panel boards, then covering each seam with thin battens. The only reason you would opt for this method over the drywall method is if you were starting on a stud wall with no drywall installed or if you planned to leave the board and batten wall raw or stained rather than painted. Of course, this method is also ideal on an exterior.
  • Over-Drywall Method: This method is outlined in the steps below. It treats your drywall as the wide boards in the board and batten look, rather than requiring the actual installation of boards. This makes the project more accessible by cutting costs and labor significantly. Because of this, this method is the most common method for interior walls.

Board and Batten Size and Spacing

Because the over-drywall method doesn't rely on the width of actual board seams for batten placement, you can really place them wherever. While placing 1x3 battens on 10- to 12-inch centers will yield the most traditional board and batten look, playing with the spacing can yield a better look that's more tailored to your space. For example, if you want a thicker batten such as a 1x4, which has an actual width of 3-1/2 inches, you'll likely want a larger space in between battens.

This will be dependent on the size of your wall and the look you're after. In a tighter space, it often looks better to opt for closer battens. However, on a large wall, spacing the battens more will keep the wall from looking too busy. In the same vein, thinner battens will look better in a smaller space, while wider ones will work in larger spaces. Remember, there are no hard and fast rules, and you can always adjust according to your preference.

How to Determine Your Board and Batten Spacing

While a quick online search will yield several calculators for determining your board and batten spacing—the easiest way is to decide how many spaces you want between the battens, then add one to this number to determine the number of battens needed. Once you determine this, input these numbers into the formula below.

Wall length in inches-(batten width X total number of battens) ÷ total number of spaces = space between battens

For example, here is what the formula would look like for a 15-foot wall with 15 spaces and 16 battens measuring 2-1/2 inches each:

180 inches - (16 x 2.5 inches) ÷ 15 = 9.33 inches

This means the battens will have 9-1/3 inches between them. Always round your number to the nearest 16th inch.

If your results of the formula yield too large of spaces between the battens, simply increase the number of battens and spaces in the formula until it yields a space width that you like. Likewise, if the spaces are too small, decrease the number of battens and spaces. Just make sure to add or subtract the same number from the battens and spacing when changing the formula. The number of battens should always be one more than the number of spaces.

Tip

Check with the hardware store or lumber yard you're shopping with. If they have a return policy for materials, it may make more sense to buy one or two extra boards. This will ensure your project doesn't come to a halt due to not having enough boards and allow you to adjust your plans if desired.

Board and Batten vs. Wainscoting

Many people use the terms "board and batten" and "wainscoting" interchangeably. The main differentiation is that wainscoting typically describes a type of trim and paneling system that covers part of the wall, most often the lower third. Additionally, wainscoting can be done in a variety of styles such as beaded paneling, flat paneling, and stile and rail, which closely resembles board and batten.

What Wood to Use for Board and Batten

Premium pine (pine with no knots) is a great, economical option for an interior board and batten feature wall. But, if you'd like to upgrade the wood and still plan on painting it, poplar is an excellent choice. While the tight, unique grain isn't known for staining, it accepts paint very well and is easy to work with, even for amateur carpenters. Additionally, poplar is more impact-resistant than many pine options.

Another popular option for the painted board and batten walls are MDF (medium-density fiberboard), which is very dimensionally stable and easy to work with. However, we don't recommend the use of MDF in areas with potential water exposure.

What You'll Need

Equipment / Tools

  • Miter saw
  • Measuring tape
  • Pencil
  • Stud finder
  • Level or laser level
  • Utility knife
  • Flat pry bar
  • Hammer
  • Brad nail gun
  • Caulk gun
  • Rag
  • Painting supplies

Materials

  • 1x4 x 8' premium pine boards
  • 1x3 x 8' premium pine boards
  • 1x2 x 8' premium pine board (optional)
  • 1-1/2" 16-gauge brad nails
  • Latex caulk
  • Construction adhesive
  • 120-grit sanding block
  • Raw wood primer
  • Latex interior paint

Instructions

How to Install a DIY Board and Batten Wall

  1. Remove Existing Baseboard

    Remove the existing baseboard and any other trim present on the wall. To do so, first, lightly score the caulk seam between the trim and the wall using a utility knife, then pry at each nail point using a flat bar.

    Tip

    If there is shoe moulding present, remove it carefully and reinstall it after installing the base of the board and batten wall.

  2. Mark Wall for Horizontal Board

    If you're installing a partial board and batten wall rather than a full wall, measure up from the floor the distance that you've specified for the wall to stop, then use a level to trace a horizontal line across the wall or set up a laser level representing the line on the wall.

    If you're installing a full-height board and batten wall, simply mount the board against the ceiling.

  3. Find and Mark Studs

    Locate the studs using a stud finder and mark them at several points from the floor to the horizontal line for future reference. Your finish nails will not always land on studs, especially when securing the battens, but the construction adhesive will hold them in place once it dries.

  4. Install Horizontal Board

    Measure the length of your wall and cut a 1x4 to length. Apply a wavy bead of construction adhesive to the back of your board, then hold the top of the board against the line, press it against the wall, and fasten it using finish nails in the studs where possible.

  5. Mount Top Trim (optional)

    On a partial board and batten wall, you have the option of placing a decorative trim board on top of the upper horizontal board. To do so, cut a 1x2 to the exact length of the horizontal board. Place a small bead of construction adhesive along the top of the horizontal board, then place the 1x2 on top of the horizontal board with its thin dimension facing the wall so the edge is overhanging, and secure in place with brad nails.

  6. Install Baseboard

    Cut and install a 1x4 (or whatever board matches your baseboards) along the floor using construction adhesive and a brad nailer.

  7. Install Corner Vertical Battens

    Cut each corner board to length, apply a wavy bead of construction adhesive to the back, then nail it in place using a brad nailer.

  8. Cut Spacer Board

    To make quick work of mounting the vertical boards, use the formula above to determine the space between each batten, then cut a scrap board exactly to this length.

  9. Cut and Mount Each Batten

    Cut each batten to the length of the space between the two horizontal boards. Starting at one of the corner boards, slide the spacer board in place, then butt the edge of the batten against the end and mount it in place.

    Continue this method on the top and bottom until you reach the other end of the wall. For extra holding power, apply a wavy bead of construction adhesive to the back of each batten.

    Warning

    There is a good chance your floor isn't perfectly level, especially in older homes. If that is the case, make sure you individually measure the length of each batten, rather than cutting them to one specific length.

  10. Sand the Boards

    Sand away any splintered edges or rough points, then lightly sand each board's edge to remove the sharp edge. This will add durability and help keep the edges from being creased as easily on impact.

  11. Prime the Boards

    Once all dust has been removed, prime the boards using a raw wood primer, following the manufacturer's instructions for application and re-coating, including sanding between coats if necessary.

  12. Caulk the Joints

    Caulk every single joint and fill any nail holes with caulk. If necessary, drive the nails further into the wood using a nail set.

  13. Paint the Boards

    Once the caulk has hardened, paint the boards and the wall with your desired paint color, applying as many coats as necessary for coverage.

How to Install a Stained Board and Batten Wall

If you desire to show off the wood grain of your board and batten wall, the installation process is similar, yet slightly more involved. The main difference is that, because you obviously can't stain drywall, you must either remove the drywall or cover it with wood.

Covering it with wood is the easiest route, but this can add nearly one inch of thickness to your board and batten wall. If that works for your space, simply cut panels using stain-grade plywood and install it over your drywall before following the steps above. Account for the need to cover the seams between plywood panels when planning your batten placements.

Tip

To elevate the look even further, swap the pine boards for wood that better accepts stain such as oak, maple, or other hardwoods.

How to Care for a Board and Batten Wall

To keep your DIY board and batten wall looking its best for years to come, regularly clean it according to the paint manufacturer's guidance. Keep any leftover paint on hand for touch-ups in the future.

FAQ

  • What kind of wood do you use for a board and batten wall?

    You can use nearly any type of wood for an interior board and batten wall. Popular options include premium pine, poplar, and even MDF. For board and batten walls that won't be painted, hardwoods such as oak and maple are great options.

  • Is board and batten an easy DIY?

    Installing board and batten in your home is an easy DIY project that nearly anyone can do. Once you figure out the best board and batten layout for your space, the installation process is quick and can be finished in one weekend.

  • Does board and batten go over drywall?

    Board and batten can easily be installed over drywall in interiors that already have drywall installed. In most scenarios, it makes more sense to use the drywall as a backer and simply attach vertical battens to the wall. Once the entire feature wall is painted, the drywall behind the battens looks like boards.

How to Install a DIY Board and Batten Wall (2024)

FAQs

How to attach board and batten to wall? ›

Attach Boards to the Wall
  1. While holding the horizontal board in place, use a nail gun to attach it to the wall.
  2. Place a nail every 10 inches or so on the top and bottom of the board to ensure it is fixed to the wall properly while the glue has time to dry.
  3. Repeat the steps with the vertical trim batten boards.

Do you nail or screw board and batten? ›

You will need at least 1-3/4” screws for the wide boards and at least 2-3/4” for the narrow battens. Boards should be screwed 2” from both the top and the bottom and then at least every 2' vertically. Nails are not recommended for exterior wood siding!

Do you nail or glue board and batten? ›

You have two options when it comes to installing the vertical batten boards:
  • Use nails only (easier to remove down the line without drywall damage)
  • Use a construction adhesive like Liquid Nails and nails (much more permanent)
Jun 2, 2021

What kind of wood is used for board and batten walls? ›

You can use nearly any type of wood for an interior board and batten wall. Popular options include premium pine, poplar, and even MDF. For board and batten walls that won't be painted, hardwoods such as oak and maple are great options.

What is the rule of thumb for board and batten? ›

While the height of board and batten is a matter of personal preference, a good rule of thumb is to place the height either above or below the center of the wall. For our eight-foot wall, we are installing board and batten at a height of five feet. For the boards, we are using 3/4" plywood.

Does board and batten have to go into studs? ›

If you're using thin, lightweight lumber, you won't need to stress about it. However, for everything else, it's a good idea to attach your boards to the studs wherever possible. If you can't find a wall stud, use wood glue/liquid nails and a nail that's long enough to secure the wood to the wall.

Do you use a brad nailer for board and batten? ›

In order to attach, I first glued each board with liquid nails for extra security, and then I nailed the pieces in with a Brad Nailer. I highly recommend using a brad nailer, so the nails are almost invisible and it has a more seamless and high-quality look to it.

Are liquid nails enough for board and batten? ›

Using Liquid Nails (the kind applied with a caulking gun) is honestly not much different than using a hot glue gun. So easy! Avoid applying too much of the adhesive close to the edge of your batten pieces so that none of the glue oozes out from behind the pieces once they are hung.

Do you nail or screw battens? ›

∎ B S 5534 'Code of practice for slating and tiling', states that the nails used for fixing tiling battens should generally have a shank diameter not less than 3.35mm. The nail is typically 65mm long to provide a minimum 40mm penetration into the rafter. Nails used in guns are generally of smaller diameter.

How thick should wood be for board and batten? ›

There are a zillion different types and sizes of wood you can use to create a board and batten wall treatment. We chose 1/4″ plywood for a couple of very important reasons. First, we wanted to work with our existing baseboards. The top of our baseboards is only 1/4 inch thick.

What is the cheapest way to do board and batten siding? ›

Fiber cement is the cheapest material for board and batten siding. It costs around $0.75 to $5 per square foot only. Fiber cement is a mixture of three different materials. Essentially, it is made by combining wood cellulose, sand, and cement.

How do you attach a wooden batten to the wall? ›

The battens should then be placed against the wall and drilled straight through with a 6mm masonry bit. Hammer in the wall and plug into the hole in the wall. Then secure the screws using an impact driver. Do this across the batten to secure it to the wall.

Do you need a nail gun for board and batten? ›

The tools I recommend having when doing a Board and Batten / wainscoting accent wall are: Miter Saw - if you are a beginner and buying your first Miter Saw, I recommend starting with a 7.25” blade which is small, less-intimidating, and easier to learn with. Nail Gun - I prefer a battery operated 18gauge Brad Nailer.

What is the best way to install board and batten siding? ›

  1. Measure and Mark the Wall. To begin, you'll need to know how much material you will need. ...
  2. Measure and Calculate the Angle (if required) ...
  3. Install House Wrap and Insulation (if required) ...
  4. Install the Boards. ...
  5. Trim Out the Borders. ...
  6. Install the Battens. ...
  7. Seal the Boards and Battens.
Dec 26, 2023

How to attach a board to a wall? ›

After getting the board where you want it, apply the adhesive and hold the cut board tightly to the wall. If you're not using an adhesive, you will first need to use a nail gun to hold the board and then you will be able to use a nail on a stud to secure the board.

References

Top Articles
Latest Posts
Article information

Author: Clemencia Bogisich Ret

Last Updated:

Views: 5650

Rating: 5 / 5 (60 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Clemencia Bogisich Ret

Birthday: 2001-07-17

Address: Suite 794 53887 Geri Spring, West Cristentown, KY 54855

Phone: +5934435460663

Job: Central Hospitality Director

Hobby: Yoga, Electronics, Rafting, Lockpicking, Inline skating, Puzzles, scrapbook

Introduction: My name is Clemencia Bogisich Ret, I am a super, outstanding, graceful, friendly, vast, comfortable, agreeable person who loves writing and wants to share my knowledge and understanding with you.